软件集成测试技术研究

首先分析了集成测试的原理和特点，并指出了集成测试的重要性。然后结合传统软件与面向对象软件开发的方法和技术，详细介绍了传统软件的集成测试方法和策略，并深入分析了面向对象软件集成测试的原理和方法。     

浅谈亚欧海底光缆S2段远供电源(PFE)及其维护管理

以亚欧海底光缆S2段为例,介绍亚欧海底光缆远供电源(PFE)的供电方式,以及其在正常运行时和故障维修时的维护管理方法。探讨在实际维护中如何贯彻落实及灵活运用系统联合维护文档,总结适合中国国情的远供电源维护经验,确保亚欧海底光缆远供电源安全稳定运行。     

对挑梁埋置砌体部分内力计算的探讨

根据前苏联M.N.高尔波诺夫-波沙道夫的<弹性地基上结构物的计算>[1]方法,结合工程设计实例,对钢筋混凝土挑梁埋置砌体部分的内力计算进行了探讨.通过对工程设计实例的分析,给工程设计人员提供了在设计中遇到类似构件时较为实用的一种精确计算方法,避免粗略计算挑梁时易造成事故隐患的缺陷.     

基于实际井眼轨迹的抽油杆柱API设计方法

目前的抽油杆柱设计方法大都基于设计井眼轨迹或经验公式，因此设计的抽油杆柱与井眼的匹配性并没有达到最优，结果可能影响了抽油杆柱的受力特性和寿命。概述了目前现有的抽油杆柱设计方法，提出了基于实际井眼轨迹的抽油杆柱API设计方法，即考虑到在三维空间中井下粘滞阻力及动载的影响，利用微单元分析方法计算出轴向载荷与轴向应力，然后在此基础上进行杆柱组合设计，并给出了设计流程。以江苏油田永21-3井为例，对几种设计方法的设计结果进行了对比分析，结果表明，江苏油田目前采用的抽油杆柱设计方法包含了人为经验因素，并不是最优的杆柱设计结果，有待进一步改进。     

基于振动参数的钻井井架安全承载力评定

通过井架结构振动理论、有限元分析和实验室简易模型的试验研究，提出了以振动频率为基准，载荷下降系数为依据诊断钻井井架结构安全承载能力的方法。根据井架的具体结构形式和受力特征，将井架简化成一根沿长度上质量均匀分布、刚度恒定的简支梁，用振动理论推导出了井架固有频率的平方与作用载荷之间存在着线性关系，并通过有限元分析对这一关系进行了验证；提出了通过测试井架在两种不同栽荷作用下的固有频率推算井架临界承载并以此评定井架安全承载能力的方法；在实验室内制作了与A型井架相类似的模型，进行了逐级载荷下的固有频率测试，分析总结出适用于井架现场评定的具体方法，最后应用此方法对现场在役井架进行了测试与安全承载能力评定。该评定方法为井架测试、安全评定提供了一个新的发展方向，对保证钻井安全将起到重要的作用。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

A multigrid accelerated hybrid unstructured mesh method for 3D compressible turbulent flow

 A cell vertex finite volume method for the solution of steady compressible turbulent flow problems on unstructured hybrid meshes of tetrahedra, prisms, pyramids and hexahedra is described. These hybrid meshes are constructed by firstly discretising the computational domain using tetrahedral elements and then by merging certain tetrahedra. A one equation turbulence model is employed and the solution of the steady flow equations is obtained by explicit relaxation. The solution process is accelerated by the addition of a multigrid method, in which the coarse meshes are generated by agglomeration, and by parallelisation. The approach is shown to be effective for the simulation of a number of 3D flows of current practical interest. Sponsored by The Research Council of Norway, project number 125676/410 Dedicated to the memory of Prof. Mike Crisfield, a respected colleague     

Fatigue crack propagation of multiple coplanar cracks with the coupled extended finite element/fast marching method

A numerical technique for modeling fatigue crack propagation of multiple coplanar cracks is presented. The proposed method couples the extended finite element method (X-FEM) [Int. J. Numer. Meth. Engng. 48 (11) (2000) 1549] to the fast marching method (FMM) [Level Set Methods & Fast Marching Methods: Evolving Interfaces in Computational Geometry, Fluid Mechanics, Computer Vision, and Materials Science, Cambridge University Press, Cambridge, UK, 1999]. The entire crack geometry, including one or more cracks, is represented by a single signed distance (level set) function. Merging of distinct cracks is handled naturally by the FMM with no collision detection or mesh reconstruction required. The FMM in conjunction with the Paris crack growth law is used to advance the crack front. In the X-FEM, a discontinuous function and the two-dimensional asymptotic crack-tip displacement fields are added to the finite element approximation to account for the crack using the notion of partition of unity [Comput. Meth. Appl. Mech. Engng. 139 (1996) 289]. This enables the domain to be modeled by a single fixed finite element mesh with no explicit meshing of the crack surfaces. In an earlier study [Engng. Fract. Mech. 70 (1) (2003) 29], the methodology, algorithm, and implementation for three-dimensional crack propagation of single cracks was introduced. In this paper, simulations for multiple planar cracks are presented, with crack merging and fatigue growth carried out without any user-intervention or remeshing.     

化学-电解氧化法制备高铁酸钾的研究

本文用化学－电解氧化法制备高铁酸钾，克服了纯化学氧化法产品需要提纯和纯电解氧化法制备周期长的缺点，得到了高纯度的高铁酸钾晶体。